Browse all practice questions for the Fire Service Pump Operator State Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Fire Service Pump Operator State Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • What is the weight of one gallon of water?
  • What is the principle of relay pumping?
  • What is a common cause of low pressure in a pump?
  • Why is low engine temperature considered bad for a pump?
  • What document outlines the standard for driver/operator professional qualifications?
  • How many gallons of water are in a cubic foot?
  • What is the primary role of a pump operator during an emergency response?
  • How many discharges must a 750 GPM pumper have as a minimum requirement?
  • What type of pressure is primarily created by a pump?
  • What is the purpose of NFPA standards in the fire service?
  • Most accidents involving emergency apparatus during the daytime happen where?
  • What pressure does a column of water one foot high exert at its base?
  • At what air pressure do air horns typically stop functioning?
  • How many cubic inches are in a gallon of water?
  • What angle should apparatus with front and rear intakes be angled towards when parked?
  • What is the primary purpose of the pump operator’s job during an incident?
  • What is the first element in learning to drive safely?
  • What is the role of a check valve in a water system?
  • What should never be connected to a hydrant?
  • What is a critical function of portable generators in firefighting?
  • What does NFPA 1002 require from operators regarding foam system testing?
  • What is the minimum pump capacity specified for pump design?
  • What must be considered when operating from an older standpipe system?
  • How does cold oil affect pump operation?
  • What does it mean when the oil gauge is fluttering?
  • Before operating a changeover valve, what should be done to the engine pressure?
  • What is the maximum output capacity of vehicle-mounted generators?
  • What happens if a hydraulic pump is not tested regularly?
  • What is the required stopping distance for new apparatus from a speed of 20 mph?
  • What is another name for head pressure in pump operations?
  • What weight does a cubic foot of water typically weigh?
  • What is the most common size water tank on a Class A pumper?
  • For fire apparatus with tanks greater than 1000 gallons, what is the required tank fill line?
  • What is NOT part of the daily apparatus inspection?
  • Centrifugal pumps can be shut down for what duration without damaging the impellers from overheating?
  • If your intake gauge shows 15 mmHg, how much lift do you have?
  • What is the standard nozzle pressure for all fog nozzles?
  • What type of pressure is vital to monitor to maintain pump efficiency during operations?
  • What is a characteristic of the pump capacity in a fire apparatus with a PTO drive?
  • At what pressure should hoses be pumped to ensure they do not exceed the annual service test?
  • When should pumpers be given a service test according to NFPA standards?
  • Where are gated intake ball valves typically located?
  • What kind of pump is best known for not having a positive blockage between its intake and discharge?
  • How many cubic inches are there in a gallon of water?
  • What is the significance of having an air intake leak in a drafting situation?
  • What occurs if a backflow preventer is not used in a water system?
  • What percentage is the friction loss in a 3 inch hose?
  • What is the critical velocity for a 3 inch hose?
  • What does static pressure represent?
  • Where is there typically no shut-off valve located during a fire service operation?
  • What is the volume of a column of water that is typically used to provide reliable fire flow?
  • Which of the following is a common component of water supply systems?
  • Which of the following weights corresponds to one gallon of water?
  • What does NFPA 1901 pertain to?
  • What type of apparatus is characterized by having a large complement of ground ladders but no aerial device?
  • What is an important safety measure regarding firefighters riding on apparatus?
  • What is the purpose of the volume series control lever?
  • If a nozzle is quickly shut down, where does the water hammer go?
  • What should the air temperature not exceed during apparatus testing?
  • At what rate does water flow through hose lines typically?
  • How should emergency vehicles distance themselves to ensure safety?
  • What is the main function of a pressure governor?
  • Where should fire apparatus protecting structures during wildland fires be parked?
  • What is the required tank fill line for fire apparatus with water tanks of 1000 gallons or less?
  • What is the maximum pump capacity limitation of PTO drive?
  • How long should the engine warm up for in non-emergency operations?
  • What should the engine RPMs be during drafting operations?
  • What is the maximum pressure for standpipes and sprinklers when supplying the FDC?
  • What is the theoretical lift in feet for fire service operations?
  • What is the maximum acceptable steering wheel play for emergency vehicles?
  • Which type of valve is most commonly used in fire service operations?
  • Which pumper has the largest capacity during a relay operation?
  • With the same size hose, friction loss varies with what factor?
  • What is the friction loss percentage in a 2 1/2 inch hose?
  • When operating with a hydrant, what is the purpose of the intake hose?
  • How long is an intake hose typically for a hydrant?
  • What is the critical velocity for a 2 1/2 inch hose?
  • If the tip size is reduced and pressure is increased but flow stays the same, what happens to the friction loss?
  • When establishing a water supply operation, what is crucial to monitor?
  • How many cubic inches are in a cubic foot?
  • At what temperature do diesel engines typically lose horsepower?
  • What is a typical consequence of running a centrifugal pump without water for an extended period?
  • What safety concern is associated with a rear pump for the driver?
  • In drafting operations, what should be the immediate action if the prime is lost?
  • What should a driver do when returning to the fire station?
  • What action should firefighters take when confronted with an exposed building that has a sprinkler system?
  • What does the term "discharge" refer to in fire service pumps?
  • What is the potential consequence of not performing routine maintenance on pumpers?
  • How can equipment failures be prevented?
  • How does atmospheric pressure change with elevation?
  • When pressure governor senses excess pressure, what action does it take?
  • How high do elevating water devices typically range?
  • What should be done if a standpipe/sprinkler system needs to raise its pressure?
  • What pressure will one psi exert in terms of feet?
  • In drafting operations, what is the role of the strainer?
  • Not being able to draft is most likely due to what?
  • What is the most common type of pumper used in fire services?
  • For a pumper with a capacity of 500 GPM or less, what is the minimum flow rate expected from the booster hose?
  • Where is the best location for the command post during an incident?
  • When raising pressure in a standpipe/sprinkler system, what is the proper increment for adjustments?
  • What does 'parallel volume' refer to in fire service operations?
  • What effect does sinuosity or zigzagging have on a hose?
  • Should firefighters be permitted to ride on the tailboard of fire apparatus?
  • What speed must a new fire apparatus be able to safely stop from?
  • What is the nozzle pressure for all fog nozzles?
  • What is the typical weight of a midi pumper chassis?
  • How many 2 1/2 inch discharges should a pumper have for every 250 GPM of capacity?
  • What is considered an overload test for pumping engines?
  • What type of systems should not exceed a pressure of 200 PSI when supplied?
  • When adjusting fire pump pressure, what is a common recommended range?
  • What does dual pumping refer to?
  • What PSI is recommended for pumpers flowing at 70% capacity?
  • How far apart should emergency vehicles traveling the same route stay?
  • How many sprinkler heads should a 1000 GMP pumper be able to supply?
  • Which is a common issue if air pressure drops below a certain level in fire service equipment?
  • What does 'series' equal in relation to firefighting equipment?
  • How many feet will one psi of pressure raise a column of water?
  • What must responding apparatus do upon encountering a school bus loading or unloading?
  • What is the maximum engine pressure allowed for older standpipe systems when supplying the FDC?
  • What is the appropriate action for firefighters if water supply from a hydrant is insufficient?
  • What is flow pressure?
  • What is the maximum output of a typical portable generator used in fire service?
  • What is the exception for pumps with a capacity of less than 750 GPM regarding certification tests?
  • When should relay pumper evolutions be shut down?
  • What is the chemical symbol for mercury?
  • For what duration should priming occur for 1250 GPM pumps?
  • What does head pressure refer to in fire service operations?
  • Where do centrifugal pumps build up pressure?
  • What fire apparatus is typically characterized as having high maneuverability and versatility?
  • What factor can significantly affect the performance of a fire service pump?
  • What is pressure in the context of firefighting and pump operations?
  • What is the standard flow rate for fire pumps mentioned in practice tests?
  • When operating an apparatus from a hydrant with supply lines of 2 1/2 inches or 3 inches, what is the maximum length allowed?
  • At what PSI should pumpers flow at 100% capacity?
  • What is a common flow rate for a standard fire hydrant?
  • What should the minimum length of a tank fill line be for fire apparatus with a water tank of 1000 gallons or less?
  • Why is a vacuum test performed on a pump?
  • In fire service terms, what does FDC stand for?
  • How many inches of mercury is equivalent to 13.55 inches of water?
  • What should a pumper's overall design facilitate?
  • Which component is most commonly checked during a daily engine start-up?
  • Driver/operator responsibilities are dictated by which documents?
  • What is typically found at the output of a centrifugal pump?
  • What is the recommended position for aerial devices when dealing with buildings that are 5 or more stories tall?
  • Under what circumstances should pressure reducing valves be removed?
  • What pressure does atmospheric pressure drop by for every 1000 feet of elevation gained?
  • What is the purpose of level one staging?
  • What is the primary concern for maintaining proper pump operation?
  • What component of the fire service system is primarily responsible for water flow?
  • How can firefighters prevent contaminated water from entering the main water system?
  • In fire service operations, what does GPM stand for?
  • What is the role of the pressure governor in a fire service pump?
  • What is the relationship between flow velocity and friction loss in hoses?
  • What should be monitored closely when drafting water from a static source?
  • Which type of pump has no positive blockage between the intake and discharge sides?
  • What is the most common diameter of LDH supply line?
  • Which type of device should be positioned next to the building for effective firefighting in high-rise scenarios?
  • What is the weight of a cubic foot of water?
  • What is the NFPA 1002 standard about?
  • Is there a shut-off valve located between the FDC and the standpipe connection?
  • What is the nozzle pressure for smooth bore master streams?
  • What is residual pressure?
  • What are the three primary ways water pressure can be created?
  • At what RPMs should the engine be set when leaving the apparatus running?
  • Which tool is instrumental for ensuring the safety and efficiency of pumping operations during a fire event?
  • What does PSF stand for in terms of measuring pressure?
  • What should be done if you notice a significant drop in pressure while pumping?
  • What is the minimum number of inches of water that should be present around the strainer in drafting operations?
  • What is level two staging used for?
  • What is the optimal condition for pumper capacity at draft?
  • At what pressure are discharge gauges typically calibrated?
  • What is the primary purpose of a changeover valve in firefighting?
  • How often should pumpers undergo a service test?
  • What does water flow regulation ensure during fire operations?
  • When should an operator be concerned about head pressure?
  • At what pressure are pumps hydrostatically tested?
  • What is the purpose of a volute in a pump?
  • Industrial foam pumpers are built according to which standards?
  • During what conditions should the source pumper operate?
  • Which of the following is a key factor in determining the effectiveness of water streams?
  • What is the weight of a 1 1/2 inch hose that is 50 feet long and full of water?
  • If the discharge pressure drops below 50 PSI during drafting operations, what should the operator do?
  • What is the nozzle pressure for smooth bore hand lines?
  • What is the main purpose of performing a vacuum test on a pump?
  • If the main valve for a sprinkler system is shut off, what will still occur?
  • How much power do inverters typically provide?
  • What is tandem pumping?
  • When do most accidents occur with fire apparatus?
  • What is considered a reliable lift measurement in feet for water?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy